Residential · Lakeland, FL
A driveway gate has to swing true, latch cleanly, and stay stable through daily use, not sag after a few months. Frontier Fences Lakeland has served homeowners and businesses since 2018, installing and repairing driveway gate systems in Lakeland with steel, aluminum, and wood frames, set on correctly built posts and hardware.
Every solid driveway gate starts with layout and a base that matches the weight and span. We verify opening width, grade, hinge side, latch side, and vehicle clearance, then set the structure around the right posts, typically 4 inch steel posts for metal gates or 6x6 pressure-treated posts for wood gates. Posts are set plumb, aligned to the string line, and installed in concrete footers sized to the gate load, with proper hinge offset so the gate clears the driveway crown. For repairs, we diagnose the cause first, failed hinges, loose post set, racked frame, dragging bottom rail, then correct the base issue before adjusting hardware.
Florida moisture, sandy soils, and wind loads can punish a driveway gate that is built light or finished poorly. We use corrosion-resistant hardware like hot-dip galvanized or stainless fasteners, sealed bearings where appropriate, and we isolate dissimilar metals to reduce galvanic corrosion. For steel we can prep, prime, and paint, and for wood we build for drainage and apply exterior stain or paint-ready surfaces, with picket spacing and rails that reduce warping. If your gate is automated, we leave room for operator brackets, clean wire routing, and safe access for future service, while keeping the finished look tight and square.
Customers choose us because the work is done like a gate contractor should do it, measured, load-rated, and built to stay aligned. Our team handles new driveway gate installation, gate sag and dragging repairs, hinge and latch replacement, post resets, frame reinforcement, and adjustments for smooth swing and reliable closure. You get clear recommendations on materials, from welded steel frames and aluminum panels to wood privacy infill, plus straight answers on what can be repaired versus what should be replaced. We show up with the right tools, post-hole augers, levels, welding equipment when needed, and we keep the site clean and controlled around driveways and vehicle access.
After installation or repair, we do a full walkthrough with you and test the gate through its full swing, checking hinge travel, latch engagement, ground clearance, and stop points. We confirm posts are stable, hardware is tightened, and the gate is braced correctly so it will not rack as it opens and closes. You receive a written estimate up front, documentation of the scope, and practical care guidance, lubrication points, finish maintenance, and what to watch for as seasons change. If your project includes automation coordination, we make sure mounting points and clearances are ready so your operator installer is not forced to improvise.
We do both. Common repairs include leaning sections, broken pickets/panels, damaged posts, loose rails, and gate hardware issues, and we will tell you when replacement is more cost-effective.
Yes, removal and haul-off can be included in the written estimate. We can also coordinate phased replacements to keep pets contained and access available.
We install vinyl, pressure-treated wood, aluminum ornamental, and galvanized chain-link fencing, plus matching walk gates and double-drive gates.
Timeline depends on footage, terrain, number of gates, and removal needs. After an on-site measure, we provide a realistic schedule and keep you updated if weather or material lead times change.
Yes. We provide a free written estimate that outlines the scope, materials, gates, and any removal or site conditions discussed on-site.
A driveway gate is part security barrier, part daily-use moving structure, and it only works well when the posts, hinges, and frame are built for the load. Frontier Fences Lakeland installs and repairs driveway gate systems for homes, farms, and commercial properties in Lakeland, with practical options in welded steel, aluminum, and wood. Whether you need a brand-new gate at a new fence line or a fix for a gate that drags, won’t latch, or leans, we focus on the base causes and a clean, durable finish.
Most driveway gate problems start at the support system, not the latch. A post that is out of plumb, an undersized footer, or hinges mounted without proper offset will cause sag, binding, and premature hardware failure. We inspect post stability, hinge wear, frame racking, and ground clearance, then correct what’s actually causing the issue. Common fixes include resetting posts in concrete, replacing worn hinge pins, adding diagonal bracing, reinforcing a cracked weld, and re-hanging the gate so it swings smoothly and lands on the stop without slamming.
For new installations, we help you choose a driveway gate style that fits your access needs and the look of your fence. Options include single-swing and double-swing layouts, welded steel frames with wood infill, aluminum panels for low maintenance, and traditional wood gates built with proper rails and bracing. We also plan for operator compatibility when automation is involved, leaving the right clearances and solid mounting points so the system is serviceable and safe.
If you want a driveway gate that closes cleanly today and still lines up months from now, start with a written plan and a properly built foundation. Tell us what you’re dealing with, stuck gate, broken hinge, leaning post, or a full new install, and we’ll provide a free written estimate with straightforward recommendations.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Lakeland. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
