Residential · Lakeland, FL
A wrought iron fence should look sharp, swing true, and stay plumb for years, not lean, rack, or rust through at the base. Frontier Fences Lakeland has served homeowners and businesses since 2018 with wrought iron fence installation, panel and gate repairs, post resets, and weld fixes in Lakeland.
Good iron work starts below grade. We lay out straight runs, verify property lines and gate clearances, then set posts to consistent depths with proper spacing for each panel and picket style. Posts are set in concrete with clean edges and correct elevation so panels sit level, gate openings stay square, and water does not pond at the base. For replacements, we remove failed footers, cut out bent or rusted post sections, and reset everything to a true line before any welding or hardware goes back on.
Florida heat, rain, and irrigation overspray are hard on metal, especially where steel meets soil and concrete. We prep by grinding scale and rust, cleaning weld zones, and sealing vulnerable points like post bottoms and rail ends, then apply a coating system matched to the job, typically a rust-inhibiting primer plus a durable black topcoat. If your fence is powder-coated, we can spot-prep and touch up properly so repairs blend and the coating stays intact. We also adjust for local conditions with smarter drainage around footers, gate hardware that tolerates frequent use, and corrosion-resistant fasteners where appropriate.
Lakeland customers choose us because we treat wrought iron fence work like metal fabrication, not a quick patch. Our crew diagnoses the cause first, hinge sag, post movement, impact damage, or corrosion, then fixes the structure so the same problem does not return next season. We handle on-site welding and reinforcement, hinge and latch upgrades, gate alignment, and section replacements while protecting surrounding pavers, landscaping, and paint. You get clear options, a written scope, and workmanship focused on straight lines, tight gaps, and smooth gate operation.
At the end of the job we do a full walkthrough and test every moving part. Gates are checked for swing, latch engagement, and consistent reveals, and we confirm panels are plumb, posts are solid, and touch-ups are complete. You receive a clean site, a free written estimate up front, and a fence that is ready for years of daily use with minimal maintenance. If we repaired rust or weld failures, we also explain what to watch for and how to wash and touch up to extend the finish life.
We do both. Common repairs include leaning sections, broken pickets/panels, damaged posts, loose rails, and gate hardware issues, and we will tell you when replacement is more cost-effective.
Yes, removal and haul-off can be included in the written estimate. We can also coordinate phased replacements to keep pets contained and access available.
We install vinyl, pressure-treated wood, aluminum ornamental, and galvanized chain-link fencing, plus matching walk gates and double-drive gates.
Timeline depends on footage, terrain, number of gates, and removal needs. After an on-site measure, we provide a realistic schedule and keep you updated if weather or material lead times change.
Yes. We provide a free written estimate that outlines the scope, materials, gates, and any removal or site conditions discussed on-site.
A wrought iron fence adds security and curb appeal, but it only performs when posts are set correctly, gates are aligned, and the coating system is maintained. Frontier Fences Lakeland installs new iron fencing and restores existing fences with practical repairs that address the root cause, from leaning posts and broken welds to dragging gates and rust at the base.
For new installs, we focus on straight layout, correct post spacing, and consistent elevation so each panel lands clean and the fence line reads true from the street. We set posts in concrete and keep gate openings square, then fit panels and gates so gaps are even and hardware operates smoothly. If you are pairing iron fencing with an existing masonry wall, columns, or slab, we plan attachment points and clearances so the job looks intentional, not pieced together.
For repairs, we commonly fix sagging gates, racked frames, and rusted post bottoms where moisture collects. That can mean cutting out deteriorated steel, welding in new material, reinforcing high-stress corners, and resetting posts rather than just tightening hinges. We also replace worn hinges, latches, drop rods, and fasteners, then prep and coat repaired areas with rust-inhibiting primer and a durable finish so the repair lasts and blends in.
Whether you need a full wrought iron fence replacement or a targeted repair, you will get a plan that prioritizes structural stability, clean welds, and a finish that stands up to Florida weather. Share your photos or schedule an onsite visit, and we will provide a free written estimate with straightforward options based on your fence’s condition and how you use the gates daily.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Lakeland. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
